Explore Now

This post in the next paragraphs pertaining to Tools You Need to Install a New Bathtub is exceptionally insightful. Check it out for your own benefit and figure out what you think about it.

Setting up a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall to eliminate the old tub and position the new tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the job and fit trying it. Instead of working with a professional to take control of a halfway-completed project, it is far better to take into consideration utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This short article will aid you mount a brand-new tub in your bathroom if you have currently gotten a new tub and also do not need to change the plan of your previous supply of water pipes.
Your tools and product list should consist of the following:

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you need to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of eliminating the existing taps can be fairly bothersome as a result of the restricted access that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Before moving on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.

Suitable New Taps

If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making sure that the washing machines remain in place in between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. When the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap connectors. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

Mounting the Bathtub

Utilizing both wood boards under its feet, place the tub in the called for position. The wooden boards are valuable in equally spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub until the spirit level reviews degree.
To install taps, fit the bottom of the outermost adaptable tap port to the proper supply pipeline by making a compression join; after that do the same for the other faucet.
Activate the supply of water as well as examine all joints and also new pipework for leaks as well as tighten them if essential. Load the bathtub and likewise examine the overflow electrical outlet and also the normal outlet for leaks.
Lastly, deal with the bath paneling as described in the producer's user's manual. Tiling and sealing around the tub ought to wait up until the tub has actually been utilized a minimum of when as this will certainly settle it into its final setting.

Getting ready for the Installation

Firstly, the supporting frame provided with the bathroom should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to see to it that if the tap includes a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its final placement.

Tiling Around the Bathtub

In the location where the bath meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to crack a stiff seal, causing the water to permeate the wall in between the bathroom as well as the tiling, bring about issues with dampness as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked paper or soft rope. Remember to always load the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealer can break relatively very early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive and also grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I am very fascinated by How to Install a Bathtub Yourself and I really hope you appreciated my blog post. For those who liked our blog entry plz be sure to share it. We cherish reading our article about How to Install a Bathtub.

Call